I want to enable Bidirectional Forwarding Detection (BFD) for my AWS Direct Connect (DX) connection.
BFD is a detection protocol to provide fast forwarding path failure detection times, which allows for a faster routing reconvergence time. BFD is a mechanism independent of media, routing protocols, or data. It's a best practice to enable BFD for fast link failure detection and failover when connecting to AWS services over DX connections and AWS VPNs. Enabling BFD for your DX connection allows the Border Gateway Protocol (BGP) neighbor relationship to be torn down quickly after notifications from BFD. Otherwise, by default, BGP waits for three keep-alive failures of 90 seconds.
Asynchronous BFD is automatically enabled for DX virtual interfaces on the AWS side. However, you must configure your router for asynchronous BFD to enable it for your connection.
Before you begin, be sure to check your vendor documentation for specific commands and instructions for configuring your network device. Then, use the following examples for Cisco and Juniper routers to configure BFD on your router.
Note: The AWS BFD liveness detection minimum interval is 300 ms and the multiplier is three.
Cisco router example configuration
The following example BFD configuration is for a Cisco router. Be sure to change this as necessary when configuring your own router.
1. Enter the following in your router's configuration terminal. Be sure to enter your own values for the interface name, virtual LAN (VLAN) number, autonomous system number (ASN), and DX peer IP address.
no ip redirect bfd slow-timers 10000 interface <YOUR_INTERFACE_NAME>.<YOUR_VLAN_NUMBER> bfd interval 300 min_rx 300 multiplier 3 router bgp <ASN> neighbor <DX Peer IP> fall-over bfd
Example configuration:
no ip redirect
bfd slow-timers 10000
interface GigabitEthernet1/0.259
description "Direct Connect to your Amazon VPC or AWS Cloud"
encapsulation dot1Q 259
ip address 169.254.254.2 255.255.255.252
bfd interval 300 min_rx 300 multiplier 3
router bgp 65000
neighbor 169.254.254.1 fail-over bfd
2. Check if BFD is enabled using:
show bfd neighbors detail
Verify that the output resembles the following:
MinTxInt: 300, MinRxInt: 300, Multiplier: 3Local Diag: 0, Demand mode: 0, Poll bit: 0 172.16.10.2 172.16.10.1 8/1 1 90 (3) Up Gi1/0.259 OurAddr NeighAddr LD/RD RH Holdown(mult) State Int
Juniper router configuration
The following example BFD configuration is for a Juniper router (JUNOS release 8.3+). Be sure to change this as necessary when configuring your own router. You can enable BFD in JUNOS using one of the following two methods.
The first method is to enable BFD using the following series of commands. Be sure to enter your own values for the group name, neighbor, and address.
cli edit protocols bgp group ebgp edit protocols bgp group GROUP-NAME NEIGHBOR ADDRESS set bfd-liveness-detection minimum-interval 300 multiplier 3 exit exit commit check commit confirm
The second method is to enable BFD at the group level.
1. Enable BFD at the group level. Be sure to enter your own value for the group name:
set protocol bgp group GROUP-NAME bfd-liveness-detection minimum-interval 300 multiplier 3
2. Verify that BFD is enabled:
show bfd session extensive
Be sure that the output resembles the following:
Address State Interface Time Interval Multiplier 192.163.6.4 Up 3.000 1.000 3 Client BGP, TX interval 0.300, RX interval 0.300 Session up time 00:54:40 Local diagnostic None, remote diagnostic None Remote state Up, version 1 Logical system 12, routing table index 25 Min async interval 1.000, min slow interval 1.000 Adaptive async TX interval 0.300, RX interval 0.300 Local min TX interval 0.300, minimum RX interval 0.300, multiplier 3 Remote min TX interval 0.300, min RX interval 0.300, multiplier 3 Local discriminator 10, remote discriminator 9 Echo mode disabled/inactive Multi-hop route table 25, local-address 192.168.6.5
Did this page help you? Yes | No
Back to the AWS Support Knowledge Center
Need help? Visit the AWS Support Center
Published: 2016-11-21
Updated: 2018-12-06